Gas Extinguish Control Panel

Product Description

1. Introduction
The ASENWARE automatic extinguisher control panel is designed in accordance with European standards EN54-2 and EN54-4 Fire Detection and Fire Alarm systems - Control and Indicating Equipment and EN12094-1 Fixed firefighting systems - Components for gas extinguishing systems - Part 1: Requirements and test methods for electrical automatic control and delay devices.
The control equipment is a combined fire alarm control panel and extinguish ing system and has three detection zones, any or all of which are capable of contributing to the extinguishant release decision.
Control panels have an integral, mains powered battery charger and power supply designed in accordance with the requirements of EN54-4.

In addition to the requirements of EN54-2 the control panel has the following facilities:

Test condition to allow the automatic resetting of zones in alarm for testing purposes. EN54-2 Section 10 option with requirements
Delay of the actioning of fire alarm devices (sounders) so that an alarm may be verified before a premises is evacuated. EN54-2 Section 7.11 option with requirements.
Fire alarm devices to enable an audible warning to be sounded throughout premises upon the detection of a fire condition or the operation of a manual call point. EN54-2 Section 7.8 option with requirements

In addition to the requirements of EN54-2, all control panels have voltage free relay contacts for fire and local fire which operate upon a fire condition. These are to be used for local control and signaling.

In addition to the requirements of EN12094-1 the control panel has the following facilities:
Delay of extinguishing signal of up to 60 seconds. EN12094-1 Section 4.17 option with requirements.

Signal representing the flow of extinguishing agent to indicate the released condition. EN12094-1 Section 4.18 option with requirements.

Monitoring of the status of components by way of a low pressure switch input. EN12094-1 Section 4.19 option with requirements.

Emergency hold device to enable the extinguishant delay time to be extended. EN12094-1 Section 4.20 option with requirements.

Control of flooding time to deactivate the releasing output after a set period of time. EN12094-1 Section 4.21 option with requirements.

Manual only mode to disable the release of extinguishant via automatic detection devices. EN12094-1 Section 4.23 option with requirements.

Triggering of equipment outside the system by way of first and second stage contacts, extract fan output etc. EN12094-1 Section 4.26 option with requirements

Activation of alarm devices with different signals to indicate pre-discharge and released warnings using different sounds. EN12094-1 Section 4.30 option with requirements.

ITEM	ELECTRICAL RATING	COMMENT
Mains supply	90 to 270VAC, 50Hz/60Hz(100 Watts maximum)
Mains supply fuse	3 Amp ( F3A L250V)	Replace only with similar type
Power supply rating	3 Amps total including battery charge 28V +/- 2V
Maximum ripple current	200 millivolts
Battery type	Two 12 Volt sealed lead acid in series.	7Ah maximum
Battery charge voltage	27.6VDC nominal
Battery charge current	0.7A maximum
Battery fuse	20mm, 3.15 glass
Current draw in mains fail condition	0.095 Amps	With buzzer sounding
Current draw in second stage alarm	0.235A	Two zones in fire(470 ohm in circuit)
Current draw in post discharge condition	0.310A	solenoid outputs active
Maximum current draw from batteries	3Amps	With main power disconnected
R0V output	Fused at 500Ma with electronic fuse
Sounder outputs	21 to 28V DC Fused at 500mA with electronic fuse	1.6Amp total load over all circuits
Fault relay contact rating	5 to 30VDC 1A Amp maximum for each	Volt free changeover contact
Fire relay contact rating	5 to 30VDC 1A Amp maximum for each	Volt free changeover contact
Local fire relay contact rating	5 to 30VDC 1A Amp maximum for each	Volt free changeover contact
First stage contact rating	5 to 30VDC 1A Amp maximum for each	Volt free changeover contact
Second stage contact rating	5 to 30VDC 1A Amp maximum for each	Volt free changeover contact
Extract contact rating	5 to 30VDC 1A Amp maximum for each	Volt free changeover contact
Zone quiescent current	0mA minimum, 2mA maximum
Terminal capacity	0.5mm 2 to 2.5mm 2 solid or stranded wire
Number of detectors per zone	Dependent on type
Number of sounders per circuit	Dependent on type and current consumption
Detection circuit end of line	6K8± 5% 1/2 Watt resistor
Monitored input end of line	6K8± 5% 1/2 Watt resistor
Sounder circuit end of line	10K± 5% 1/2 Watt resistor
Extinguishant output end of line	1N4004 Diode
No. of detection circuits	Four 21 to 28V DC
No. of sounder circuits	Three 21 to 28V DC	2X first stage, 1 X second stage
Extinguishant release output	21V to 28V DC. Maximum load 1 Amp
Extinguishant release delay	Adjustable 0 to 75 seconds	5 second steps
SIL, AL, FLT, RST inputs	Switched – ve, min resistance 0 ohms, max 470 ohms
Zone normal threshold (Allowable EOL)	10K ohms to 2K ohms	Use 6K8 end of line resistor
Detector alarm threshold	1K ohms to 390 ohms
Call point alarm threshold	370 ohms to 150 ohms
Short circuit threshold	130 ohms to 0 ohms
Head removal condition	15.5 to 17.5 volts+/- 5%
Cabling	FP200 or equivalent	Metal cable glands must be used.
Monitored inputs normal threshold	10K ohms to 2K ohms
(Allowable EOL)	10K ohms to 2K ohms
Monitored inputs alarm threshold	2K ohms to 150 ohms+/-5%
Monitored inputs Short circuit threshold	140 ohms to 0 ohms+/-5%
Status unit/Ancillary board connection	Two wire RS485 connection with electronic fuse.	Max. of 16 units-RS485 data cable
Status unit power output	21 to 28V DC, Fused at 500mA with electronic fuse.	300 milliamp maximum load

More Product Features


Trademark:	ASENWARE
Model NO.:	AW-GEC2158
Standard:	CE
Productivity:	10000PCS/Year
Origin:	China
Packing:	Carton
Type:	Fire Extinguisher
Company:	Shenzhen Widesense Technology Co., Ltd.