Z-Wave Plus Smart Light Dimmer Plug Built-in Zwave Repeater/Range Extender Zwave Hub Required Smart Electrical Plug Works with Smartthings, Wink

Introduce
This is a switch plug-in and is used between a standard wall outlet and electrical loads connected to a wall outlet by cable. The unit is rated IP 20 and can, therefore, be used in dry environments only. The device switches all kinds of loads. The unit is included in a Z-Wave network by remote control, PC software, or any other kind of Z-Wave controller.

Product Specifications

Primary View
Remote control of two smart outlets separately-- control your lights and small appliances from anywhere 
 A built-in Z-Wave signal repeater which will increase your Z-Wave mesh network and overall speed
Ability to still use your top outlet -- Plug this in the bottom outlet & you will still be able to use the top In addition, this version has the following improvements:
Auto-Inclusion no more pressing buttons -- plug it in and it will automatically include/pair
Remembers the last state after a power outage*
White LED light can be disabled by holding down the button for 10 seconds

Plug the smart outlet in, control, and dim your lights from anywhere, schedule a timed event, or create a custom scene from anywhere in the world, at any time of the day.
Adjust brightness level from 10-100% - Manual & Remote Control cuts energy costs and extends bulb life.
Plug and Play- The wall plug adds to your Z-Wave hub in minutes. Z-Wave Plus dim control for 120V light devices, max loading 500W.
Works with Alexa for voice control (Alexa device and hub sold separately). Compatible with the following Z-Wave certified Hubs: SmartThings, Wink, ADT Pulse, Trane, Nexia, Honeywell, HomeSeer, Harmony Home Hub Extender, Vera, Connect and Iris.
Once plugged in, the Wall Plug acts as a signal repeater that strengthens Z-Wave signals and boosts connectivity between hub and devices. NOTE: Z-Wave gateway controller required- sold separately.


Installation
1.Getting To Know Your New Z-Wave Device
Must not exceed 600 watts (Incandescent): 1200W (10A) Resistive or ½ HP
Motor. The total load capacity for both outlets is 1200W (10A) Resistive.
• One Z-Wave controlled AC outlet for standard incandescent light, CFL/LED, fans or small appliances
• Remote ON/OFF control via the Z-Wave controller
• Manual ON/OFF control with the front panel push button
• One always-on pass-through AC outlet
• Space-efficient design
• Does not block the lower outlet when plugged into the upper outlet of a duplex wall receptacle
(This assumes that the duplex receptacle is mounted with the ground pin down).
• Plugs and cords for connected devices route to the side allowing close placement of furniture
• Grounded 3-wire power connection for safety
2.
A. Z-Wave controlled outlet(1channel)
This outlet can remotely turn On/Off the connected device
B. Manual/Program button
Single press - turn the lamp On/Off
Single press - include or exclude in Z-Wave network
C. Z-Wave controlled outlet(2channel)
This outlet can remotely turn On/Off the connected device

3. The title goes here.
1. Plug the light you want to control into the Z-Wave controlled smart outlet on the wireless switch as indicated by the Z-Wave logo
NOTE: Plug directly into an outlet, do not use with extension cords
2. Plug the wireless smart switch directly into an available grounded outlet (Top outlet recommend if possible).
TO return your switch to factory default:
1. I plugged in, unplug the smart switch from the receptacle.
2. Press and hold the top button for at least 3 seconds while you plug the smart switch into a receptacle.
3. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.

4.Adding a device to the Z-Wave network:
1. Follow the instructions for your Z-Wave certified controller to include a device to the Z-Wave network.
2. Once the controller is ready to include your device, press up and release the toggle to include it in the network.
3. Once your controller has confirmed that the device has been included, refresh the Z-Wave network to optimize performance.
4. The device is associated with the same group when it included in the setting process.
Now you can control your Z-wave device according to groups, scenes, schedules, and automation programmed. If your controller features remote access, you can now control all devices in the Z-Wave network from mobile devices.

If any product meets your demand, please contact Allison for further information.