Basic Info.
Model NO.
10.7Mhz/HM HM10M7.5A
Transfer Function
Band Pass
Product Description
HMCF1200
center frequency:10.7Mhz
1dB bandwidth : 10 khz min
60dB width : 30 khz max
ripple :1.0dB
insertion loss :3.0dB
Stoppard attention:60dB
Group delay time :20uSec
NO. | Item | Specification |
4 - 1 | f0 (6dB) Center Frequency f0 (Center of 6dB Bandwidth) | 10.7MHz |
4 - 2 | (1dB) Bandwidth(1dB) | 10 KHz min |
(6dB) Bandwidth(6dB) | 12 kHz min |
(60dB) Bandwidth(60dB) | 30 kHz min |
4 - 3 | (fo±1000KHz) Stop Band Attenuation | 60dB min |
4 - 4 | (f0±10khz) Ripple (f0±10khz) | 1.0dB max |
4 - 5 | Insertion Loss (At minimum loss point) | 3.0dB max |
4 - 6 | (-20ºC~ +80ºC ) Temperature Stability (-20ºC~ +80ºC ) | ±0.5% max (-25ºC ~ +80ºC) |
4-7 | (0.1~1MHz)Spurious Response | 20dB min |
4-8 | (fo±3.0 kHz)GDT Ripple deviation | 20μsec max |
4-9 | Operating Temperature | -20ºC ~ +80ºC |
4-10 | Storage Temperature | -40ºC ~ +85ºC |
4-11 | Insulation Resistance(DC 25V 1 minute) | 100MΩ min |
4 - 12 | / Input/Output Impedance | 50 Ω |
NO. | Item | Measurement condition | Requirement |
7-1 |
Random Drop | 0.3 3 . Filter shall be measured after 3 times random drops from the height of 30cm on concrete floor | , 1. No visible damage and it meet Table 1 |
7-2 | | 1.5mm,10-55Hz. | , |
,2 |
. | 1. |
Vibration | Filter shall be measured after being applied | No damage and it meet |
vibration of amplitude of 1.5mm with 10-55Hz | Table 1. |
band of vibration frequency to each of 3 |
perpendicular directions for 2 hours |
7-3 | Solderability | 5 ,230 | 95% |
±5ºC3±0.5 . Lead terminals are immersed in aide solder for 5 sec and then immersed in soldering bath of | . At least 95% lead terminals shall be covered |
230±5ºC, for 3±0.5 sec. | with solder. |
7-4 |
Substrate Bending Test | 0.5mm |
It shall meet table 1. 1. |
|
(3),3mm,30 Apply pressure in the direction of arrow (see Fig. 3) at a rate of about 0.5mm per second until it |
reaches a |
bend of 3mm and hold for 30 seconds. |
7-5 |
| 20N |
It shall meet Table 1. |
|
(4),10 . |
|
,. |
Adhesion | A static load of 20N to the direction of the | 1. |
arrow (see |
Fig. 4) shall be applied on the core of the |
component |
and hold for 10 seconds. Filter shall be |
| | soldered correctly and tightly to PCB. | |
7-6 |
Reflow Soldering | (5), |
It shall meet Table 1. 1. |
|
24 . Put on the solder paste on the printed wiring board (pattern is shown in Fig. 5), the samples |
shall be mounted and soldered under the |
condition (pattern is shown in Fig. 6), then it |
shall be subjected to the room atmosphere for |
24 hours prior to the measurement. |
Item | Specification |
Center Frequency | 10.7 MHz |
(1dB) Bandwidth(1dB) | 10 KHz min |
(60dB) Selectivity(60dB) | 30 KHz max |
(fo±1000KHz) Stop Band Attenuation | 60 dB min |
Ripple | 1.0dB max |
Insertion Loss | 3.0dB max |
Address:
Dongjiang Town Golden Bay Industrial Zone, Wuxi, Jiangsu, China
Business Type:
Manufacturer/Factory
Business Range:
Auto, Motorcycle Parts & Accessories, Electrical & Electronics, Industrial Equipment & Components, Manufacturing & Processing Machinery
Management System Certification:
ISO 9001, ISO 14001
Company Introduction:
We have 30 years of design experience, excellent processing and manufacturing team, the quality is our consistent pursuit.
High-precision machining parts is our best at the product, oil seals, bushings, and other rotating precision products is our strength.