Basic Info.
Product Description
Features:Adopt new microprocessor technology and robust structural designNot applicable to rotating prism, electronic scanning is adoptedAccurate and reliable position detection of hot metals reaching and exceeding 300 ºCAdopt signal comparison technology-remove background infrared noise interferenceThe measurement is not affected by local heat source in the market, lens dust and field water vaporThe scanning field of view angle is 1° × 15°The position of the measured object is displayed by using rod-shaped LED luminous tubeThe response time is 1ms and digitally adjustable in the range of 1-250msInstrument power-on self-inspection or remote control self-inspectionRelay output, photoelectric isolation output, transistor output PNP/NPNIt also has AC AC80-240V and DC DC24V power supply interfaceCast aluminum shell has unique purging and cooling functions, and air and water cooling are optionalMSE-PF100 electronic scanning thermal metal detector uses linear germanium diode arrayBrief introduction of principle
MSE-PF100 scanning thermal inspection uses electronic scanning instead of traditional optical cooling scanning, which omits the maintenance of rotating parts and improves the scanning reliability. However, the traditional static analog thermal detection HMD only uses a photodiode to detect infrared signals exceeding the set threshold, which is easily affected by water mist and field background thermal radiation.
Electronic scanning thermal inspection can realize rapid and accurate detection of the head and tail edges of rods and wires or rigidity by using microprocessor technology, and the response time is digitally adjustable. The LED bar-shaped display bar at the back of the sensor can not only display the position of the measured object, but also accurately adjust various parameters.
Main technical parameters| Parameter | Indicators | Parameter | Indicators |
| Typical application | 350 ºC, 10mm rod
Detect from 2 meters | Power supply
Voltage | 24VDC ± 15% |
350 ºC, 50mm rod,
Detect from 4 meters | Power | 5VA |
| Detecting device | Electronically scanned
Germanium diode array | Work
Temperature | -10-+ 50 ºC without cooling |
| Scanning rate | 1200 beats/sec | Cooling with air at 70 ºC |
| Response time | 1-250ms digital adjustable | Cool with water at 80 ºC |
| Minimum product temperature | 300 ºC | Self-inspection | Power-on self-inspection: self-inspection of instrument after power-on
Remote control self-test: remote trigger, continuous detection |
Products
Position display | 10 LED display arrays | Output (1) | Relay output: (normally open) 240VAC 10A, 20W, 4ms response time |
| Scanning angle | Standard: 1°x 15°
| Output (2) | Optical isolation output: 300VAC 150mA
200mW, 2ms response time |
| Detection technology | Adopt the technology of comparing the intensity of signal and background thermal radiation-remove the interference of background infrared noise | Output (3) | NPN & PNP output: 400mA,
45V. 2A peak |
| Materials | AI6 cast aluminum, high temperature sprayed | Cooling mode | Air cooling + air purging; Water cooling + air purging |
| Protection level | IEC IP66, DIN 89011 | Air pressure | 5-15PSI, flow rate: 28-140L/min |
| Weight | 1.9 kg | Water pressure | 5-10PSI, flow rate: 0.2-0.3 L/min |
| Cable joint | IP65 | Water temperature | Use cooling water at 20 ºC when the ambient temperature is lower than 70 ºC |
| Length | 2 metres | Use cooling water at 5 ºC when the ambient temperature is higher than 80 ºC |
Typical applicationGeneral application: Detect hot metal products with temperature exceeding 300 ºCFor hot strip mill: Accurate and rapid detection of head and tail position (for length measurement and optimized shearing)For bars and profiles: in the background (roller table) thermal radiation and bar thermal radiation is very close to the occasion;Quickly detect the head and tail of hot metal where water mist and steam often appearIt has nothing to do with volume, temperature and shape, but it requires high edge detection of hot metal
Address:
Kexin Building, 212 Changjiang Road,Yantai Development Zone, Shandong, China
Business Type:
Manufacturer/Factory, Other
Business Range:
Industrial Equipment & Components, Instruments & Meters
Company Introduction:
We are an engineering company in Yantai with German management and German investment. We develop, produce and market non-contact optical sensors and measuring systems for velocity, length, distance, width, thickness, level and position of cold as well as hot material.
){kind=link}