Small Logo Hot Foil Stamping Machine

 

main features:
1. The use of a pneumatic cylinder powered actuator movement is stable and reliable.
2. The work process without impact, can greatly improve work efficiency, processing quality and die life.
3. Hands button operation, safe; (footswitch optional spare, release your hands to improve work efficiency).
4. Stamping pressure, adjustable temperature.
5. Stamping head height adjustable lift.
6. Automatic counting function.
Third, the technical parameters:
Operating voltage: AC220V 50HZ;
Working pressure: 0.2-0.8MPA (2-8kg / cm3);
Working environment: -5 ºC ~ 50 ºC.
Power: 500-1000W
Temperature range: 0-399 degrees
Product Specifications: 300X280X750mm
Body weight: 35kg
Packaging: individual wooden
Table size 160 * 170mm
Heating plate area: 100 * 100mm or 150 * 120mm (can contact our order non-standard specifications)
 
Fourth, the initial use:
 
1. When delivery, depending on the spot inspection of goods, there are components damaged, and logistics staff pointed directly and contact our company. Consumable parts: air source processor, the button.
 
2. Remove the transportation of wooden boxes, in this process, please pay attention to protect components.
 
3. Place the machine to the work surface, make sure that the level of stability. Install transit detached wearing components, check for loose wires, prolapse.
 
4. From the pump, the output a pipe connected to the gas source processor machine inlet end with C-type quick connector.
 
 
 
 
 
Note: When ventilation cylinder, the piston rod will rise rapidly, easily lead to danger. So this, stand side punch operations, so that the body away from the top of the piston rod.
 
 
 
5. Connect AC220V mains, turn the power button on the control box, turn off the manual and automatic temperature control switch two buttons, press both buttons or foot switch is depressed, the cylinder fall; release the button, the cylinder rises.
 
 
 
Fourth, the role of various components of the machine and adjust
 
First, the mold mounting
 
    Mold can be installed in two ways: high-temperature plastic adhesive, open screw holes with screws.
 
1. High-temperature plastic adhesive:
 
The mold and the heating plates are clean, apply a small amount of mold on the back of high-temperature plastic, coated with a spatula after the flat, heating plate affixed to the appropriate location, to be high-temperature curing adhesive, can be used. High-temperature plastic should not be too much impact adhesive effect.
 
2. Open screw holes for fixing screws:
 
    Remove the heating plate, choose the right location, milling machines are openings in the heating plate and the mold, tapping, and finally the use of screws.
 
Second, adjusting the mold
 
    Mold control has adjustable height adjustment, levelness.
 
1. Height adjustment:
 
 
 
 
Rough height adjustment: the height of the workpiece, adjusting cap imprinted machine. Loosen up and down the two screws 3, 4 and tighten top screws, 2 trumpeters wheel rotation adjustment, the upper end cap adjusted up and down. After adjusting to the appropriate position, release the 4th top tight screws, tighten the two screws on the 3rd and down.
 
Precision height adjustment: by adjustable knob cylinder (Exhibit 1), under the pressure of cylinder stroke is adjusted so that the contact surface of the die and the workpiece to achieve the best results.
 
 
 
1. Levelness adjustment:
 
Under the pressure of the heating plate to the work surface, the level of observation. Adjusting nut 7 downwards, make up the heating plate. 8 upward adjustment nut can make the heating plate down. Followed by adjusting the four directions of the nuts, and then adjusted to a level, tighten the four nut. Four eight tie bars designed for the Division I first nut, stamping avoid problems caused by the uneven heating caused by uneven board.
 
 
 
A pressure regulator
 
The main pressure regulator is adjusted by installing a filter on the machine will be shown the black pull up the handle 6 clockwise to increase pressure, counterclockwise to reduce the pressure. Watch barometer, pressure is set to a reasonable range, after adjustment is complete, press the black handle lock.
 
63 cylinder working range of 3-8 kg at 7 kg pressure, the actual output can reach 120 kg.
 
 
 
Second, the speed regulator
 
    Speed adjustment, mainly through adjustable throttle cylinder mounted on the machine to adjust the throttle bolt 5 shown adjusted clockwise to slow the speed of the cylinder under pressure, counterclockwise to accelerate the speed of the cylinder under pressure.
 
 
 
Third, the delay adjustment and temperature adjustment
 
1. delay adjustment
 
    Open 16 delay switch, adjust 4 delay setting knob to set the required length of time delay, adjustable 0-10 sec. In this case, press the button (or foot switch), under pressure cylinder, release the button (or foot switch), the delay continues to power the solenoid valve, until the end of the set time, the cylinder rises, complete workflow.
 
 
 
2. Temperature adjustment
 
    Open the thermostat switch 15, 11 temperature display will appear red numbers, indicating the current heating plate temperature. Setting the thermostat setting button 13, select the appropriate temperature, when the heating plate temperature below the set temperature, the thermostat starts to work, 12 work lights. When the temperature reaches the set temperature, the thermostat stops working, 12 light does not work. Under normal circumstances, the heat pipe with heat, the initial heating, the heating plate temperature will be higher than the set temperature 10-30 ° (about the size of the power and heat pipe), this phenomenon is normal.
 
First, the test machine
 
According to the above steps to set up your machine, respectively adjust different temperature, pressure, time delay, test machine, through incremental approach to achieve the desired effect.
 
 
 
 
 
Routine Maintenance
 
 
 
1. Please control the assembly diagrams check for proper installation
 
2. Check the various parts of the loose screw nut is like
 
3. Check pipe connections are correct, with special attention to the airflow direction air source processor, according to air preparation
 
4. Direction of the arrow on the ventilation
 
5. One can choose the turbine oil for lubrication, the use of turbine oil One, the need to always check the gas source processor Run
 
6. Oil quantity, to ensure the normal lubrication
 
7. Feel free to check gas source processor drainage is normal, ensure air entering the cylinder does not contain moisture
 
8. Please keep the device clean.