Home
Product Directory
Electrical & Electronics
Telecommunication & Broadcasting
Communication Module
Find Similar Products
Product Description
Company Info
Product Description
E1/FiberEth serial interface converter used back multiplexing technology, transfers 10M/100M Ethernet data by E1 channels. It realizes conversion between 1*E1 channel and Ethernet optical interface. It can transmit signal of E1 channel to Ethernet optical interface point to point, realizing the connection of E1 channel and Ethernet.
Product Features
-Realize transparent transfer Ethernet data in 1 E1 channels
-10M/100M Ethernet, full/half duplex self adapt, support VLAN.
-Ethernet support AUTO-MDIX( cross over and straight through self adapt)
-Setting CRC alarm limitation to auto isolate lines with low transfer quality, single direction. When one direction error rate over limitation, disconnect only one direction, the other is not affected. Unbalance in two directions.
-Allow 1 E1 channels up to 10ms transfer delay. When the delay over the limitation, can stop transfer automatically.
-Have 2 loop back functions: E1 local loop, E1 external loop.
-Support Dynamic Ethernet MAC address(4096), having local address filter function.
-E1 interface compatible with ITU-T G. 703, G. 704, and G. 823. Signaling slot not supported.
-E1 interface having internal clock resume circuit and HDB3 codec circuit.
- Support E1 channel hot plug, and auto detect available E1 channels not pause the transmission.
-Supporting 1 E1 channels customized configuration, auto detect the number of E1 channels and select the available E1 at reset.
-E1 Support 75Ω/unbalance impedance or 120Ω/balance for order
-Support reset remote system from local system.
-Have Ethernet monitor auto reset function.
-Support SNMP netwok managemetn for chassis version or standalone unit.
Technical Specification
E1 Interface
-Line Rate: 2.048Mbps+/-50ppm
-Line Code: HDB3
-Interface Standard: ITU-T G. 703
-E1 Impedance: 75Ω(unbalance) or 120Ω(balance)
-Connections: Dual coax BNC and 120-ohm twisted-pair (RJ45)
-Jitter tolerance: Finer than G. 742 and G. 823
Fiber connector
-Optical interface: SC/FC
-Rate: 10/100 auto-negotiation
-Optical Wavelenth: FP1310 nm DFB1550nm+/-50/40nm
-Sending power consumption: -9dBm/-5dBm
-Receiving and dispatching module: >-6dBm
-Optical receiver receiving sensitivity: <-36 (BER<10 -10):
-Dynamic range receiving: >-30dB
-Optical code: NRZ
-Support several optical interface:
-850nm/1310nm multi-mode fiber,
-1310nm/1550nm single-mode fiber.
-Transmit distance: Multi-mode with 2KM, single-mode with 20KM, 40KM, 60KM, and 120KM.
Power supply
-working voltage range wide, good
-anti-disturb and Isolation, work stable
-option I - DC-48V, range DC-36V~DC-72C
-Option II - AC220V, range AC165V~AC240V
-Power Consumption: <=3 Watts
Environment condition
-Operating temperature: 0C~+50 C
-Storage temperature: -20 C~+70 C
-Relative temperature: 95% (uncondensed)
Product Features
-Realize transparent transfer Ethernet data in 1 E1 channels
-10M/100M Ethernet, full/half duplex self adapt, support VLAN.
-Ethernet support AUTO-MDIX( cross over and straight through self adapt)
-Setting CRC alarm limitation to auto isolate lines with low transfer quality, single direction. When one direction error rate over limitation, disconnect only one direction, the other is not affected. Unbalance in two directions.
-Allow 1 E1 channels up to 10ms transfer delay. When the delay over the limitation, can stop transfer automatically.
-Have 2 loop back functions: E1 local loop, E1 external loop.
-Support Dynamic Ethernet MAC address(4096), having local address filter function.
-E1 interface compatible with ITU-T G. 703, G. 704, and G. 823. Signaling slot not supported.
-E1 interface having internal clock resume circuit and HDB3 codec circuit.
- Support E1 channel hot plug, and auto detect available E1 channels not pause the transmission.
-Supporting 1 E1 channels customized configuration, auto detect the number of E1 channels and select the available E1 at reset.
-E1 Support 75Ω/unbalance impedance or 120Ω/balance for order
-Support reset remote system from local system.
-Have Ethernet monitor auto reset function.
-Support SNMP netwok managemetn for chassis version or standalone unit.
Technical Specification
E1 Interface
-Line Rate: 2.048Mbps+/-50ppm
-Line Code: HDB3
-Interface Standard: ITU-T G. 703
-E1 Impedance: 75Ω(unbalance) or 120Ω(balance)
-Connections: Dual coax BNC and 120-ohm twisted-pair (RJ45)
-Jitter tolerance: Finer than G. 742 and G. 823
Fiber connector
-Optical interface: SC/FC
-Rate: 10/100 auto-negotiation
-Optical Wavelenth: FP1310 nm DFB1550nm+/-50/40nm
-Sending power consumption: -9dBm/-5dBm
-Receiving and dispatching module: >-6dBm
-Optical receiver receiving sensitivity: <-36 (BER<10 -10):
-Dynamic range receiving: >-30dB
-Optical code: NRZ
-Support several optical interface:
-850nm/1310nm multi-mode fiber,
-1310nm/1550nm single-mode fiber.
-Transmit distance: Multi-mode with 2KM, single-mode with 20KM, 40KM, 60KM, and 120KM.
Power supply
-working voltage range wide, good
-anti-disturb and Isolation, work stable
-option I - DC-48V, range DC-36V~DC-72C
-Option II - AC220V, range AC165V~AC240V
-Power Consumption: <=3 Watts
Environment condition
-Operating temperature: 0C~+50 C
-Storage temperature: -20 C~+70 C
-Relative temperature: 95% (uncondensed)
Address:
Nanshan Hi-Tech Park, Shenzhen, Guangdong, China
Business Type:
Manufacturer/Factory, Trading Company
Business Range:
Computer Products, Electrical & Electronics
Company Introduction:
Shenzhen Angellcom Technology Co., Ltd is founded in January 2000. Based in Shenzhen, a first Special Economic Zone in China, it enjoys the convenient supply chain and rich Hi-Tech talents over here. The founders of Angellcom have been driven by an aggressive market penetration strategy, with a healthy balance of investment risks and reward.
Shenzhen Angellcom Technology Co., Ltd mainly focuses on "last mile"technology and dedicated to bring cost-effective solutions to customers. The products range includes interface converter, PDH Multiplexer, Fiber Modem, RS232 serial converter, xDSL modem, media converter, VoIP solutions, TDM over IP, etc. Meanwhile, following the fast pace of market developing, with rich expertise, Angellcom is always able to develop customerized products for customers.
In past years, Angellcom has established good relationship with telecom operators, government, and enterprises and provided satisfied products and solutions to the customers. Our products are also exported to other countries and regions such as South Asia, Middle East, Latin America and got good response from our foreign customers.
Shenzhen Angellcom Technology Co., Ltd mainly focuses on "last mile"technology and dedicated to bring cost-effective solutions to customers. The products range includes interface converter, PDH Multiplexer, Fiber Modem, RS232 serial converter, xDSL modem, media converter, VoIP solutions, TDM over IP, etc. Meanwhile, following the fast pace of market developing, with rich expertise, Angellcom is always able to develop customerized products for customers.
In past years, Angellcom has established good relationship with telecom operators, government, and enterprises and provided satisfied products and solutions to the customers. Our products are also exported to other countries and regions such as South Asia, Middle East, Latin America and got good response from our foreign customers.
Send your message to this supplier
